libata: PATA driver for Celleb

This is the patch for PATA controller of Celleb.

This driver uses the managed iomap (devres).

Because this driver needs special taskfile accesses, there is
a copy of ata_std_softreset(). ata_dev_try_classify() is exported
so that it can be used in this function.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

drivers/ata/Kconfig

@@ -562,6 +562,15 @@ config PATA_IXP4XX_CF
 
 	  If unsure, say N.
 
+config PATA_SCC
+	tristate "Toshiba's Cell Reference Set IDE support"
+	depends on PCI
+	help
+	  This option enables support for the built-in IDE controller on
+	  Toshiba Cell Reference Board.
+
+	  If unsure, say N.
+
 endif
 endmenu
 

drivers/ata/Makefile

@@ -59,6 +59,7 @@ obj-$(CONFIG_PATA_WINBOND_VLB)	+= pata_winbond.o
 obj-$(CONFIG_PATA_SIS)		+= pata_sis.o
 obj-$(CONFIG_PATA_TRIFLEX)	+= pata_triflex.o
 obj-$(CONFIG_PATA_IXP4XX_CF)	+= pata_ixp4xx_cf.o
+obj-$(CONFIG_PATA_SCC)		+= pata_scc.o
 obj-$(CONFIG_PATA_PLATFORM)	+= pata_platform.o
 # Should be last but one libata driver
 obj-$(CONFIG_ATA_GENERIC)	+= ata_generic.o

drivers/ata/libata-core.c

@@ -708,7 +708,7 @@ unsigned int ata_dev_classify(const struct ata_taskfile *tf)
  *	Device type - %ATA_DEV_ATA, %ATA_DEV_ATAPI or %ATA_DEV_NONE.
  */
 
-static unsigned int
+unsigned int
 ata_dev_try_classify(struct ata_port *ap, unsigned int device, u8 *r_err)
 {
 	struct ata_taskfile tf;
@@ -6311,3 +6311,4 @@ EXPORT_SYMBOL_GPL(ata_irq_on);
 EXPORT_SYMBOL_GPL(ata_dummy_irq_on);
 EXPORT_SYMBOL_GPL(ata_irq_ack);
 EXPORT_SYMBOL_GPL(ata_dummy_irq_ack);
+EXPORT_SYMBOL_GPL(ata_dev_try_classify);

drivers/ata/pata_scc.c

+/*
+ * Support for IDE interfaces on Celleb platform
+ *
+ * (C) Copyright 2006 TOSHIBA CORPORATION
+ *
+ * This code is based on drivers/ata/ata_piix.c:
+ *  Copyright 2003-2005 Red Hat Inc
+ *  Copyright 2003-2005 Jeff Garzik
+ *  Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
+ *  Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ *  Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
+ *
+ * and drivers/ata/ahci.c:
+ *  Copyright 2004-2005 Red Hat, Inc.
+ *
+ * and drivers/ata/libata-core.c:
+ *  Copyright 2003-2004 Red Hat, Inc.  All rights reserved.
+ *  Copyright 2003-2004 Jeff Garzik
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME		"pata_scc"
+#define DRV_VERSION		"0.1"
+
+#define PCI_DEVICE_ID_TOSHIBA_SCC_ATA		0x01b4
+
+/* PCI BARs */
+#define SCC_CTRL_BAR		0
+#define SCC_BMID_BAR		1
+
+/* offset of CTRL registers */
+#define SCC_CTL_PIOSHT		0x000
+#define SCC_CTL_PIOCT		0x004
+#define SCC_CTL_MDMACT		0x008
+#define SCC_CTL_MCRCST		0x00C
+#define SCC_CTL_SDMACT		0x010
+#define SCC_CTL_SCRCST		0x014
+#define SCC_CTL_UDENVT		0x018
+#define SCC_CTL_TDVHSEL 	0x020
+#define SCC_CTL_MODEREG 	0x024
+#define SCC_CTL_ECMODE		0xF00
+#define SCC_CTL_MAEA0		0xF50
+#define SCC_CTL_MAEC0		0xF54
+#define SCC_CTL_CCKCTRL 	0xFF0
+
+/* offset of BMID registers */
+#define SCC_DMA_CMD		0x000
+#define SCC_DMA_STATUS		0x004
+#define SCC_DMA_TABLE_OFS	0x008
+#define SCC_DMA_INTMASK 	0x010
+#define SCC_DMA_INTST		0x014
+#define SCC_DMA_PTERADD 	0x018
+#define SCC_REG_CMD_ADDR	0x020
+#define SCC_REG_DATA		0x000
+#define SCC_REG_ERR		0x004
+#define SCC_REG_FEATURE 	0x004
+#define SCC_REG_NSECT		0x008
+#define SCC_REG_LBAL		0x00C
+#define SCC_REG_LBAM		0x010
+#define SCC_REG_LBAH		0x014
+#define SCC_REG_DEVICE		0x018
+#define SCC_REG_STATUS		0x01C
+#define SCC_REG_CMD		0x01C
+#define SCC_REG_ALTSTATUS	0x020
+
+/* register value */
+#define TDVHSEL_MASTER		0x00000001
+#define TDVHSEL_SLAVE		0x00000004
+
+#define MODE_JCUSFEN		0x00000080
+
+#define ECMODE_VALUE		0x01
+
+#define CCKCTRL_ATARESET	0x00040000
+#define CCKCTRL_BUFCNT		0x00020000
+#define CCKCTRL_CRST		0x00010000
+#define CCKCTRL_OCLKEN		0x00000100
+#define CCKCTRL_ATACLKOEN	0x00000002
+#define CCKCTRL_LCLKEN		0x00000001
+
+#define QCHCD_IOS_SS		0x00000001
+
+#define QCHSD_STPDIAG		0x00020000
+
+#define INTMASK_MSK		0xD1000012
+#define INTSTS_SERROR		0x80000000
+#define INTSTS_PRERR		0x40000000
+#define INTSTS_RERR		0x10000000
+#define INTSTS_ICERR		0x01000000
+#define INTSTS_BMSINT		0x00000010
+#define INTSTS_BMHE		0x00000008
+#define INTSTS_IOIRQS		0x00000004
+#define INTSTS_INTRQ		0x00000002
+#define INTSTS_ACTEINT		0x00000001
+
+
+/* PIO transfer mode table */
+/* JCHST */
+static const unsigned long JCHSTtbl[2][7] = {
+	{0x0E, 0x05, 0x02, 0x03, 0x02, 0x00, 0x00},	/* 100MHz */
+	{0x13, 0x07, 0x04, 0x04, 0x03, 0x00, 0x00}	/* 133MHz */
+};
+
+/* JCHHT */
+static const unsigned long JCHHTtbl[2][7] = {
+	{0x0E, 0x02, 0x02, 0x02, 0x02, 0x00, 0x00},	/* 100MHz */
+	{0x13, 0x03, 0x03, 0x03, 0x03, 0x00, 0x00}	/* 133MHz */
+};
+
+/* JCHCT */
+static const unsigned long JCHCTtbl[2][7] = {
+	{0x1D, 0x1D, 0x1C, 0x0B, 0x06, 0x00, 0x00},	/* 100MHz */
+	{0x27, 0x26, 0x26, 0x0E, 0x09, 0x00, 0x00}	/* 133MHz */
+};
+
+/* DMA transfer mode  table */
+/* JCHDCTM/JCHDCTS */
+static const unsigned long JCHDCTxtbl[2][7] = {
+	{0x0A, 0x06, 0x04, 0x03, 0x01, 0x00, 0x00},	/* 100MHz */
+	{0x0E, 0x09, 0x06, 0x04, 0x02, 0x01, 0x00}	/* 133MHz */
+};
+
+/* JCSTWTM/JCSTWTS  */
+static const unsigned long JCSTWTxtbl[2][7] = {
+	{0x06, 0x04, 0x03, 0x02, 0x02, 0x02, 0x00},	/* 100MHz */
+	{0x09, 0x06, 0x04, 0x02, 0x02, 0x02, 0x02}	/* 133MHz */
+};
+
+/* JCTSS */
+static const unsigned long JCTSStbl[2][7] = {
+	{0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x00},	/* 100MHz */
+	{0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x05}	/* 133MHz */
+};
+
+/* JCENVT */
+static const unsigned long JCENVTtbl[2][7] = {
+	{0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x00},	/* 100MHz */
+	{0x02, 0x02, 0x02, 0x02, 0x02, 0x02, 0x02}	/* 133MHz */
+};
+
+/* JCACTSELS/JCACTSELM */
+static const unsigned long JCACTSELtbl[2][7] = {
+	{0x00, 0x00, 0x00, 0x00, 0x01, 0x01, 0x00},	/* 100MHz */
+	{0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01}	/* 133MHz */
+};
+
+static const struct pci_device_id scc_pci_tbl[] = {
+	{PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_SCC_ATA,
+	 PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+	{ }	/* terminate list */
+};
+
+/**
+ *	scc_set_piomode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: um
+ *
+ *	Set PIO mode for device.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void scc_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+	unsigned int pio = adev->pio_mode - XFER_PIO_0;
+	void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR];
+	void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL;
+	void __iomem *piosht_port = ctrl_base + SCC_CTL_PIOSHT;
+	void __iomem *pioct_port = ctrl_base + SCC_CTL_PIOCT;
+	unsigned long reg;
+	int offset;
+
+	reg = in_be32(cckctrl_port);
+	if (reg & CCKCTRL_ATACLKOEN)
+		offset = 1;	/* 133MHz */
+	else
+		offset = 0;	/* 100MHz */
+
+	reg = JCHSTtbl[offset][pio] << 16 | JCHHTtbl[offset][pio];
+	out_be32(piosht_port, reg);
+	reg = JCHCTtbl[offset][pio];
+	out_be32(pioct_port, reg);
+}
+
+/**
+ *	scc_set_dmamode - Initialize host controller PATA DMA timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: um
+ *	@udma: udma mode, 0 - 6
+ *
+ *	Set UDMA mode for device.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void scc_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+	unsigned int udma = adev->dma_mode;
+	unsigned int is_slave = (adev->devno != 0);
+	u8 speed = udma;
+	void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR];
+	void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL;
+	void __iomem *mdmact_port = ctrl_base + SCC_CTL_MDMACT;
+	void __iomem *mcrcst_port = ctrl_base + SCC_CTL_MCRCST;
+	void __iomem *sdmact_port = ctrl_base + SCC_CTL_SDMACT;
+	void __iomem *scrcst_port = ctrl_base + SCC_CTL_SCRCST;
+	void __iomem *udenvt_port = ctrl_base + SCC_CTL_UDENVT;
+	void __iomem *tdvhsel_port = ctrl_base + SCC_CTL_TDVHSEL;
+	int offset, idx;
+
+	if (in_be32(cckctrl_port) & CCKCTRL_ATACLKOEN) 
+		offset = 1;	/* 133MHz */
+	else
+		offset = 0;	/* 100MHz */
+
+	if (speed >= XFER_UDMA_0)
+		idx = speed - XFER_UDMA_0;
+	else
+		return;
+
+	if (is_slave) {
+		out_be32(sdmact_port, JCHDCTxtbl[offset][idx]);
+		out_be32(scrcst_port, JCSTWTxtbl[offset][idx]);
+		out_be32(tdvhsel_port,
+			 (in_be32(tdvhsel_port) & ~TDVHSEL_SLAVE) | (JCACTSELtbl[offset][idx] << 2));
+	} else {
+		out_be32(mdmact_port, JCHDCTxtbl[offset][idx]);
+		out_be32(mcrcst_port, JCSTWTxtbl[offset][idx]);
+		out_be32(tdvhsel_port,
+			 (in_be32(tdvhsel_port) & ~TDVHSEL_MASTER) | JCACTSELtbl[offset][idx]);
+	}
+	out_be32(udenvt_port,
+		 JCTSStbl[offset][idx] << 16 | JCENVTtbl[offset][idx]);
+}
+
+/**
+ *	scc_tf_load - send taskfile registers to host controller
+ *	@ap: Port to which output is sent
+ *	@tf: ATA taskfile register set
+ *
+ *	Note: Original code is ata_tf_load().
+ */
+
+static void scc_tf_load (struct ata_port *ap, const struct ata_taskfile *tf)
+{
+	struct ata_ioports *ioaddr = &ap->ioaddr;
+	unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
+
+	if (tf->ctl != ap->last_ctl) {
+		out_be32(ioaddr->ctl_addr, tf->ctl);
+		ap->last_ctl = tf->ctl;
+		ata_wait_idle(ap);
+	}
+
+	if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
+		out_be32(ioaddr->feature_addr, tf->hob_feature);
+		out_be32(ioaddr->nsect_addr, tf->hob_nsect);
+		out_be32(ioaddr->lbal_addr, tf->hob_lbal);
+		out_be32(ioaddr->lbam_addr, tf->hob_lbam);
+		out_be32(ioaddr->lbah_addr, tf->hob_lbah);
+		VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
+			tf->hob_feature,
+			tf->hob_nsect,
+			tf->hob_lbal,
+			tf->hob_lbam,
+			tf->hob_lbah);
+	}
+
+	if (is_addr) {
+		out_be32(ioaddr->feature_addr, tf->feature);
+		out_be32(ioaddr->nsect_addr, tf->nsect);
+		out_be32(ioaddr->lbal_addr, tf->lbal);
+		out_be32(ioaddr->lbam_addr, tf->lbam);
+		out_be32(ioaddr->lbah_addr, tf->lbah);
+		VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
+			tf->feature,
+			tf->nsect,
+			tf->lbal,
+			tf->lbam,
+			tf->lbah);
+	}
+
+	if (tf->flags & ATA_TFLAG_DEVICE) {
+		out_be32(ioaddr->device_addr, tf->device);
+		VPRINTK("device 0x%X\n", tf->device);
+	}
+
+	ata_wait_idle(ap);
+}
+
+/**
+ *	scc_check_status - Read device status reg & clear interrupt
+ *	@ap: port where the device is
+ *
+ *	Note: Original code is ata_check_status().
+ */
+
+static u8 scc_check_status (struct ata_port *ap)
+{
+	return in_be32(ap->ioaddr.status_addr);
+}
+
+/**
+ *	scc_tf_read - input device's ATA taskfile shadow registers
+ *	@ap: Port from which input is read
+ *	@tf: ATA taskfile register set for storing input
+ *
+ *	Note: Original code is ata_tf_read().
+ */
+
+static void scc_tf_read (struct ata_port *ap, struct ata_taskfile *tf)
+{
+	struct ata_ioports *ioaddr = &ap->ioaddr;
+
+	tf->command = scc_check_status(ap);
+	tf->feature = in_be32(ioaddr->error_addr);
+	tf->nsect = in_be32(ioaddr->nsect_addr);
+	tf->lbal = in_be32(ioaddr->lbal_addr);
+	tf->lbam = in_be32(ioaddr->lbam_addr);
+	tf->lbah = in_be32(ioaddr->lbah_addr);
+	tf->device = in_be32(ioaddr->device_addr);
+
+	if (tf->flags & ATA_TFLAG_LBA48) {
+		out_be32(ioaddr->ctl_addr, tf->ctl | ATA_HOB);
+		tf->hob_feature = in_be32(ioaddr->error_addr);
+		tf->hob_nsect = in_be32(ioaddr->nsect_addr);
+		tf->hob_lbal = in_be32(ioaddr->lbal_addr);
+		tf->hob_lbam = in_be32(ioaddr->lbam_addr);
+		tf->hob_lbah = in_be32(ioaddr->lbah_addr);
+	}
+}
+
+/**
+ *	scc_exec_command - issue ATA command to host controller
+ *	@ap: port to which command is being issued
+ *	@tf: ATA taskfile register set
+ *
+ *	Note: Original code is ata_exec_command().
+ */
+
+static void scc_exec_command (struct ata_port *ap,
+			      const struct ata_taskfile *tf)
+{
+	DPRINTK("ata%u: cmd 0x%X\n", ap->id, tf->command);
+
+	out_be32(ap->ioaddr.command_addr, tf->command);
+	ata_pause(ap);
+}
+
+/**
+ *	scc_check_altstatus - Read device alternate status reg
+ *	@ap: port where the device is
+ */
+
+static u8 scc_check_altstatus (struct ata_port *ap)
+{
+	return in_be32(ap->ioaddr.altstatus_addr);
+}
+
+/**
+ *	scc_std_dev_select - Select device 0/1 on ATA bus
+ *	@ap: ATA channel to manipulate
+ *	@device: ATA device (numbered from zero) to select
+ *
+ *	Note: Original code is ata_std_dev_select().
+ */
+
+static void scc_std_dev_select (struct ata_port *ap, unsigned int device)
+{
+	u8 tmp;
+
+	if (device == 0)
+		tmp = ATA_DEVICE_OBS;
+	else
+		tmp = ATA_DEVICE_OBS | ATA_DEV1;
+
+	out_be32(ap->ioaddr.device_addr, tmp);
+	ata_pause(ap);
+}
+
+/**
+ *	scc_bmdma_setup - Set up PCI IDE BMDMA transaction
+ *	@qc: Info associated with this ATA transaction.
+ *
+ *	Note: Original code is ata_bmdma_setup().
+ */
+
+static void scc_bmdma_setup (struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
+	u8 dmactl;
+	void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+	/* load PRD table addr */
+	out_be32(mmio + SCC_DMA_TABLE_OFS, ap->prd_dma);
+
+	/* specify data direction, triple-check start bit is clear */
+	dmactl = in_be32(mmio + SCC_DMA_CMD);
+	dmactl &= ~(ATA_DMA_WR | ATA_DMA_START);
+	if (!rw)
+		dmactl |= ATA_DMA_WR;
+	out_be32(mmio + SCC_DMA_CMD, dmactl);
+
+	/* issue r/w command */
+	ap->ops->exec_command(ap, &qc->tf);
+}
+
+/**
+ *	scc_bmdma_start - Start a PCI IDE BMDMA transaction
+ *	@qc: Info associated with this ATA transaction.
+ *
+ *	Note: Original code is ata_bmdma_start().
+ */
+
+static void scc_bmdma_start (struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	u8 dmactl;
+	void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+	/* start host DMA transaction */
+	dmactl = in_be32(mmio + SCC_DMA_CMD);
+	out_be32(mmio + SCC_DMA_CMD, dmactl | ATA_DMA_START);
+}
+
+/**
+ *	scc_devchk - PATA device presence detection
+ *	@ap: ATA channel to examine
+ *	@device: Device to examine (starting at zero)
+ *
+ *	Note: Original code is ata_devchk().
+ */
+
+static unsigned int scc_devchk (struct ata_port *ap,
+				unsigned int device)
+{
+	struct ata_ioports *ioaddr = &ap->ioaddr;
+	u8 nsect, lbal;
+
+	ap->ops->dev_select(ap, device);
+
+	out_be32(ioaddr->nsect_addr, 0x55);
+	out_be32(ioaddr->lbal_addr, 0xaa);
+
+	out_be32(ioaddr->nsect_addr, 0xaa);
+	out_be32(ioaddr->lbal_addr, 0x55);
+
+	out_be32(ioaddr->nsect_addr, 0x55);
+	out_be32(ioaddr->lbal_addr, 0xaa);
+
+	nsect = in_be32(ioaddr->nsect_addr);
+	lbal = in_be32(ioaddr->lbal_addr);
+
+	if ((nsect == 0x55) && (lbal == 0xaa))
+		return 1;	/* we found a device */
+
+	return 0;		/* nothing found */
+}
+
+/**
+ *	scc_bus_post_reset - PATA device post reset
+ *
+ *	Note: Original code is ata_bus_post_reset().
+ */
+
+static void scc_bus_post_reset (struct ata_port *ap, unsigned int devmask)
+{
+	struct ata_ioports *ioaddr = &ap->ioaddr;
+	unsigned int dev0 = devmask & (1 << 0);
+	unsigned int dev1 = devmask & (1 << 1);
+	unsigned long timeout;
+
+	/* if device 0 was found in ata_devchk, wait for its
+	 * BSY bit to clear
+	 */
+	if (dev0)
+		ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);
+
+	/* if device 1 was found in ata_devchk, wait for
+	 * register access, then wait for BSY to clear
+	 */
+	timeout = jiffies + ATA_TMOUT_BOOT;
+	while (dev1) {
+		u8 nsect, lbal;
+
+		ap->ops->dev_select(ap, 1);
+		nsect = in_be32(ioaddr->nsect_addr);
+		lbal = in_be32(ioaddr->lbal_addr);
+		if ((nsect == 1) && (lbal == 1))
+			break;
+		if (time_after(jiffies, timeout)) {
+			dev1 = 0;
+			break;
+		}
+		msleep(50);	/* give drive a breather */
+	}
+	if (dev1)
+		ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);
+
+	/* is all this really necessary? */
+	ap->ops->dev_select(ap, 0);
+	if (dev1)
+		ap->ops->dev_select(ap, 1);
+	if (dev0)
+		ap->ops->dev_select(ap, 0);
+}
+
+/**
+ *	scc_bus_softreset - PATA device software reset
+ *
+ *	Note: Original code is ata_bus_softreset().
+ */
+
+static unsigned int scc_bus_softreset (struct ata_port *ap,
+				       unsigned int devmask)
+{
+	struct ata_ioports *ioaddr = &ap->ioaddr;
+
+	DPRINTK("ata%u: bus reset via SRST\n", ap->id);
+
+	/* software reset.  causes dev0 to be selected */
+	out_be32(ioaddr->ctl_addr, ap->ctl);
+	udelay(20);
+	out_be32(ioaddr->ctl_addr, ap->ctl | ATA_SRST);
+	udelay(20);
+	out_be32(ioaddr->ctl_addr, ap->ctl);
+
+	/* spec mandates ">= 2ms" before checking status.
+	 * We wait 150ms, because that was the magic delay used for
+	 * ATAPI devices in Hale Landis's ATADRVR, for the period of time
+	 * between when the ATA command register is written, and then
+	 * status is checked.  Because waiting for "a while" before
+	 * checking status is fine, post SRST, we perform this magic
+	 * delay here as well.
+	 *
+	 * Old drivers/ide uses the 2mS rule and then waits for ready
+	 */
+	msleep(150);
+
+	/* Before we perform post reset processing we want to see if
+	 * the bus shows 0xFF because the odd clown forgets the D7
+	 * pulldown resistor.
+	 */
+	if (scc_check_status(ap) == 0xFF)
+		return 0;
+
+	scc_bus_post_reset(ap, devmask);
+
+	return 0;
+}
+
+/**
+ *	scc_std_softreset - reset host port via ATA SRST
+ *	@ap: port to reset
+ *	@classes: resulting classes of attached devices
+ *
+ *	Note: Original code is ata_std_softreset().
+ */
+
+static int scc_std_softreset (struct ata_port *ap, unsigned int *classes)
+{
+	unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
+	unsigned int devmask = 0, err_mask;
+	u8 err;
+
+	DPRINTK("ENTER\n");
+
+	if (ata_port_offline(ap)) {
+		classes[0] = ATA_DEV_NONE;
+		goto out;
+	}
+
+	/* determine if device 0/1 are present */
+	if (scc_devchk(ap, 0))
+		devmask |= (1 << 0);
+	if (slave_possible && scc_devchk(ap, 1))
+		devmask |= (1 << 1);
+
+	/* select device 0 again */
+	ap->ops->dev_select(ap, 0);
+
+	/* issue bus reset */
+	DPRINTK("about to softreset, devmask=%x\n", devmask);
+	err_mask = scc_bus_softreset(ap, devmask);
+	if (err_mask) {
+		ata_port_printk(ap, KERN_ERR, "SRST failed (err_mask=0x%x)\n",
+				err_mask);
+		return -EIO;
+	}
+
+	/* determine by signature whether we have ATA or ATAPI devices */
+	classes[0] = ata_dev_try_classify(ap, 0, &err);
+	if (slave_possible && err != 0x81)
+		classes[1] = ata_dev_try_classify(ap, 1, &err);
+
+ out:
+	DPRINTK("EXIT, classes[0]=%u [1]=%u\n", classes[0], classes[1]);
+	return 0;
+}
+
+/**
+ *	scc_bmdma_stop - Stop PCI IDE BMDMA transfer
+ *	@qc: Command we are ending DMA for
+ */
+
+static void scc_bmdma_stop (struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR];
+	void __iomem *bmid_base = ap->host->iomap[SCC_BMID_BAR];
+	u32 reg;
+
+	while (1) {
+		reg = in_be32(bmid_base + SCC_DMA_INTST);
+
+		if (reg & INTSTS_SERROR) {
+			printk(KERN_WARNING "%s: SERROR\n", DRV_NAME);
+			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_SERROR|INTSTS_BMSINT);
+			out_be32(bmid_base + SCC_DMA_CMD,
+				 in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
+			continue;
+		}
+
+		if (reg & INTSTS_PRERR) {
+			u32 maea0, maec0;
+			maea0 = in_be32(ctrl_base + SCC_CTL_MAEA0);
+			maec0 = in_be32(ctrl_base + SCC_CTL_MAEC0);
+			printk(KERN_WARNING "%s: PRERR [addr:%x cmd:%x]\n", DRV_NAME, maea0, maec0);
+			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_PRERR|INTSTS_BMSINT);
+			out_be32(bmid_base + SCC_DMA_CMD,
+				 in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
+			continue;
+		}
+
+		if (reg & INTSTS_RERR) {
+			printk(KERN_WARNING "%s: Response Error\n", DRV_NAME);
+			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_RERR|INTSTS_BMSINT);
+			out_be32(bmid_base + SCC_DMA_CMD,
+				 in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
+			continue;
+		}
+
+		if (reg & INTSTS_ICERR) {
+			out_be32(bmid_base + SCC_DMA_CMD,
+				 in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
+			printk(KERN_WARNING "%s: Illegal Configuration\n", DRV_NAME);
+			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_ICERR|INTSTS_BMSINT);
+			continue;
+		}
+
+		if (reg & INTSTS_BMSINT) {
+			unsigned int classes;
+			printk(KERN_WARNING "%s: Internal Bus Error\n", DRV_NAME);
+			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_BMSINT);
+			/* TBD: SW reset */
+			scc_std_softreset(ap, &classes);
+			continue;
+		}
+
+		if (reg & INTSTS_BMHE) {
+			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_BMHE);
+			continue;
+		}
+
+		if (reg & INTSTS_ACTEINT) {
+			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_ACTEINT);
+			continue;
+		}
+
+		if (reg & INTSTS_IOIRQS) {
+			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_IOIRQS);
+			continue;
+		}
+		break;
+	}
+
+	/* clear start/stop bit */
+	out_be32(bmid_base + SCC_DMA_CMD,
+		 in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
+
+	/* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */
+	ata_altstatus(ap);	/* dummy read */
+}
+
+/**
+ *	scc_bmdma_status - Read PCI IDE BMDMA status
+ *	@ap: Port associated with this ATA transaction.
+ */
+
+static u8 scc_bmdma_status (struct ata_port *ap)
+{
+	u8 host_stat;
+	void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+	host_stat = in_be32(mmio + SCC_DMA_STATUS);
+
+	/* Workaround for PTERADD: emulate DMA_INTR when 
+	 * - IDE_STATUS[ERR] = 1
+	 * - INT_STATUS[INTRQ] = 1
+	 * - DMA_STATUS[IORACTA] = 1
+	 */
+	if (!(host_stat & ATA_DMA_INTR)) {
+		u32 int_status = in_be32(mmio + SCC_DMA_INTST);
+		if (ata_altstatus(ap) & ATA_ERR &&
+		    int_status & INTSTS_INTRQ &&
+		    host_stat & ATA_DMA_ACTIVE)
+			host_stat |= ATA_DMA_INTR;
+	}
+
+	return host_stat;
+}
+
+/**
+ *	scc_data_xfer - Transfer data by PIO
+ *	@adev: device for this I/O
+ *	@buf: data buffer
+ *	@buflen: buffer length
+ *	@write_data: read/write
+ *
+ *	Note: Original code is ata_data_xfer().
+ */
+
+static void scc_data_xfer (struct ata_device *adev, unsigned char *buf,
+			   unsigned int buflen, int write_data)
+{
+	struct ata_port *ap = adev->ap;
+	unsigned int words = buflen >> 1;
+	unsigned int i;
+	u16 *buf16 = (u16 *) buf;
+	void __iomem *mmio = ap->ioaddr.data_addr;
+
+	/* Transfer multiple of 2 bytes */
+	if (write_data) {
+		for (i = 0; i < words; i++)
+			out_be32(mmio, cpu_to_le16(buf16[i]));
+	} else {
+		for (i = 0; i < words; i++)
+			buf16[i] = le16_to_cpu(in_be32(mmio));
+	}
+
+	/* Transfer trailing 1 byte, if any. */
+	if (unlikely(buflen & 0x01)) {
+		u16 align_buf[1] = { 0 };
+		unsigned char *trailing_buf = buf + buflen - 1;
+
+		if (write_data) {
+			memcpy(align_buf, trailing_buf, 1);
+			out_be32(mmio, cpu_to_le16(align_buf[0]));
+		} else {
+			align_buf[0] = le16_to_cpu(in_be32(mmio));
+			memcpy(trailing_buf, align_buf, 1);
+		}
+	}
+}
+
+/**
+ *	scc_irq_on - Enable interrupts on a port.
+ *	@ap: Port on which interrupts are enabled.
+ *
+ *	Note: Original code is ata_irq_on().
+ */
+
+static u8 scc_irq_on (struct ata_port *ap)
+{
+	struct ata_ioports *ioaddr = &ap->ioaddr;
+	u8 tmp;
+
+	ap->ctl &= ~ATA_NIEN;
+	ap->last_ctl = ap->ctl;
+
+	out_be32(ioaddr->ctl_addr, ap->ctl);
+	tmp = ata_wait_idle(ap);
+
+	ap->ops->irq_clear(ap);
+
+	return tmp;
+}
+
+/**
+ *	scc_irq_ack - Acknowledge a device interrupt.
+ *	@ap: Port on which interrupts are enabled.
+ *
+ *	Note: Original code is ata_irq_ack().
+ */
+
+static u8 scc_irq_ack (struct ata_port *ap, unsigned int chk_drq)
+{
+	unsigned int bits = chk_drq ? ATA_BUSY | ATA_DRQ : ATA_BUSY;
+	u8 host_stat, post_stat, status;
+
+	status = ata_busy_wait(ap, bits, 1000);
+	if (status & bits)
+		if (ata_msg_err(ap))
+			printk(KERN_ERR "abnormal status 0x%X\n", status);
+
+	/* get controller status; clear intr, err bits */
+	host_stat = in_be32(ap->ioaddr.bmdma_addr + SCC_DMA_STATUS);
+	out_be32(ap->ioaddr.bmdma_addr + SCC_DMA_STATUS,
+		 host_stat | ATA_DMA_INTR | ATA_DMA_ERR);
+
+	post_stat = in_be32(ap->ioaddr.bmdma_addr + SCC_DMA_STATUS);
+
+	if (ata_msg_intr(ap))
+		printk(KERN_INFO "%s: irq ack: host_stat 0x%X, new host_stat 0x%X, drv_stat 0x%X\n",
+		       __FUNCTION__,
+		       host_stat, post_stat, status);
+
+	return status;
+}
+
+/**
+ *	scc_bmdma_freeze - Freeze BMDMA controller port
+ *	@ap: port to freeze
+ *
+ *	Note: Original code is ata_bmdma_freeze().
+ */
+
+static void scc_bmdma_freeze (struct ata_port *ap)
+{
+	struct ata_ioports *ioaddr = &ap->ioaddr;
+
+	ap->ctl |= ATA_NIEN;
+	ap->last_ctl = ap->ctl;
+
+	out_be32(ioaddr->ctl_addr, ap->ctl);
+
+	/* Under certain circumstances, some controllers raise IRQ on
+	 * ATA_NIEN manipulation.  Also, many controllers fail to mask
+	 * previously pending IRQ on ATA_NIEN assertion.  Clear it.
+	 */
+	ata_chk_status(ap);
+
+	ap->ops->irq_clear(ap);
+}
+
+/**
+ *	scc_pata_prereset - prepare for reset
+ *	@ap: ATA port to be reset
+ */
+
+static int scc_pata_prereset (struct ata_port *ap)
+{
+	ap->cbl = ATA_CBL_PATA80;
+	return ata_std_prereset(ap);
+}
+
+/**
+ *	scc_std_postreset - standard postreset callback
+ *	@ap: the target ata_port
+ *	@classes: classes of attached devices
+ *
+ *	Note: Original code is ata_std_postreset().
+ */
+
+static void scc_std_postreset (struct ata_port *ap, unsigned int *classes)
+{
+	DPRINTK("ENTER\n");
+
+	/* re-enable interrupts */
+	if (!ap->ops->error_handler)
+		ap->ops->irq_on(ap);
+
+	/* is double-select really necessary? */
+	if (classes[0] != ATA_DEV_NONE)
+		ap->ops->dev_select(ap, 1);
+	if (classes[1] != ATA_DEV_NONE)
+		ap->ops->dev_select(ap, 0);
+
+	/* bail out if no device is present */
+	if (classes[0] == ATA_DEV_NONE && classes[1] == ATA_DEV_NONE) {
+		DPRINTK("EXIT, no device\n");
+		return;
+	}
+
+	/* set up device control */
+	if (ap->ioaddr.ctl_addr)
+		out_be32(ap->ioaddr.ctl_addr, ap->ctl);
+
+	DPRINTK("EXIT\n");
+}
+
+/**
+ *	scc_error_handler - Stock error handler for BMDMA controller
+ *	@ap: port to handle error for
+ */
+
+static void scc_error_handler (struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, scc_pata_prereset, scc_std_softreset, NULL,
+			   scc_std_postreset);
+}
+
+/**
+ *	scc_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt.
+ *	@ap: Port associated with this ATA transaction.
+ *
+ *	Note: Original code is ata_bmdma_irq_clear().
+ */
+
+static void scc_bmdma_irq_clear (struct ata_port *ap)
+{
+	void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+	if (!mmio)
+		return;
+
+	out_be32(mmio + SCC_DMA_STATUS, in_be32(mmio + SCC_DMA_STATUS));
+}
+
+/**
+ *	scc_port_start - Set port up for dma.
+ *	@ap: Port to initialize
+ *
+ *	Allocate space for PRD table using ata_port_start().
+ *	Set PRD table address for PTERADD. (PRD Transfer End Read)
+ */
+
+static int scc_port_start (struct ata_port *ap)
+{
+	void __iomem *mmio = ap->ioaddr.bmdma_addr;
+	int rc;
+
+	rc = ata_port_start(ap);
+	if (rc)
+		return rc;
+
+	out_be32(mmio + SCC_DMA_PTERADD, ap->prd_dma);
+	return 0;
+}
+
+/**
+ *	scc_port_stop - Undo scc_port_start()
+ *	@ap: Port to shut down
+ *
+ *	Reset PTERADD.
+ */
+
+static void scc_port_stop (struct ata_port *ap)
+{
+	void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+	out_be32(mmio + SCC_DMA_PTERADD, 0);
+}
+
+static struct scsi_host_template scc_sht = {
+	.module			= THIS_MODULE,
+	.name			= DRV_NAME,
+	.ioctl			= ata_scsi_ioctl,
+	.queuecommand		= ata_scsi_queuecmd,
+	.can_queue		= ATA_DEF_QUEUE,
+	.this_id		= ATA_SHT_THIS_ID,
+	.sg_tablesize		= LIBATA_MAX_PRD,
+	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
+	.emulated		= ATA_SHT_EMULATED,
+	.use_clustering		= ATA_SHT_USE_CLUSTERING,
+	.proc_name		= DRV_NAME,
+	.dma_boundary		= ATA_DMA_BOUNDARY,
+	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
+	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
+};
+
+static const struct ata_port_operations scc_pata_ops = {
+	.port_disable		= ata_port_disable,
+	.set_piomode		= scc_set_piomode,
+	.set_dmamode		= scc_set_dmamode,
+	.mode_filter		= ata_pci_default_filter,
+
+	.tf_load		= scc_tf_load,
+	.tf_read		= scc_tf_read,
+	.exec_command		= scc_exec_command,
+	.check_status		= scc_check_status,
+	.check_altstatus	= scc_check_altstatus,
+	.dev_select		= scc_std_dev_select,
+
+	.bmdma_setup		= scc_bmdma_setup,
+	.bmdma_start		= scc_bmdma_start,
+	.bmdma_stop		= scc_bmdma_stop,
+	.bmdma_status		= scc_bmdma_status,
+	.data_xfer		= scc_data_xfer,
+
+	.qc_prep		= ata_qc_prep,
+	.qc_issue		= ata_qc_issue_prot,
+
+	.freeze			= scc_bmdma_freeze,
+	.error_handler		= scc_error_handler,
+	.post_internal_cmd	= scc_bmdma_stop,
+
+	.irq_handler		= ata_interrupt,
+	.irq_clear		= scc_bmdma_irq_clear,
+	.irq_on			= scc_irq_on,
+	.irq_ack		= scc_irq_ack,
+
+	.port_start		= scc_port_start,
+	.port_stop		= scc_port_stop,
+};
+
+static struct ata_port_info scc_port_info[] = {
+	{
+		.sht		= &scc_sht,
+		.flags		= ATA_FLAG_SLAVE_POSS | ATA_FLAG_MMIO | ATA_FLAG_NO_LEGACY,
+		.pio_mask	= 0x1f,	/* pio0-4 */
+		.mwdma_mask	= 0x00,
+		.udma_mask	= ATA_UDMA6,
+		.port_ops	= &scc_pata_ops,
+	},
+};
+
+/**
+ *	scc_reset_controller - initialize SCC PATA controller.
+ */
+
+static int scc_reset_controller(struct ata_probe_ent *probe_ent)
+{
+	void __iomem *ctrl_base = probe_ent->iomap[SCC_CTRL_BAR];
+	void __iomem *bmid_base = probe_ent->iomap[SCC_BMID_BAR];
+	void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL;
+	void __iomem *mode_port = ctrl_base + SCC_CTL_MODEREG;
+	void __iomem *ecmode_port = ctrl_base + SCC_CTL_ECMODE;
+	void __iomem *intmask_port = bmid_base + SCC_DMA_INTMASK;
+	void __iomem *dmastatus_port = bmid_base + SCC_DMA_STATUS;
+	u32 reg = 0;
+
+	out_be32(cckctrl_port, reg);
+	reg |= CCKCTRL_ATACLKOEN;
+	out_be32(cckctrl_port, reg);
+	reg |= CCKCTRL_LCLKEN | CCKCTRL_OCLKEN;
+	out_be32(cckctrl_port, reg);
+	reg |= CCKCTRL_CRST;
+	out_be32(cckctrl_port, reg);
+
+	for (;;) {
+		reg = in_be32(cckctrl_port);
+		if (reg & CCKCTRL_CRST)
+			break;
+		udelay(5000);
+	}
+
+	reg |= CCKCTRL_ATARESET;
+	out_be32(cckctrl_port, reg);
+	out_be32(ecmode_port, ECMODE_VALUE);
+	out_be32(mode_port, MODE_JCUSFEN);
+	out_be32(intmask_port, INTMASK_MSK);
+
+	if (in_be32(dmastatus_port) & QCHSD_STPDIAG) {
+		printk(KERN_WARNING "%s: failed to detect 80c cable. (PDIAG# is high)\n", DRV_NAME);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+/**
+ *	scc_setup_ports - initialize ioaddr with SCC PATA port offsets.
+ *	@ioaddr: IO address structure to be initialized
+ *	@base: base address of BMID region
+ */
+
+static void scc_setup_ports (struct ata_ioports *ioaddr, void __iomem *base)
+{
+	ioaddr->cmd_addr = base + SCC_REG_CMD_ADDR;
+	ioaddr->altstatus_addr = ioaddr->cmd_addr + SCC_REG_ALTSTATUS;
+	ioaddr->ctl_addr = ioaddr->cmd_addr + SCC_REG_ALTSTATUS;
+	ioaddr->bmdma_addr = base;
+	ioaddr->data_addr = ioaddr->cmd_addr + SCC_REG_DATA;
+	ioaddr->error_addr = ioaddr->cmd_addr + SCC_REG_ERR;
+	ioaddr->feature_addr = ioaddr->cmd_addr + SCC_REG_FEATURE;
+	ioaddr->nsect_addr = ioaddr->cmd_addr + SCC_REG_NSECT;
+	ioaddr->lbal_addr = ioaddr->cmd_addr + SCC_REG_LBAL;
+	ioaddr->lbam_addr = ioaddr->cmd_addr + SCC_REG_LBAM;
+	ioaddr->lbah_addr = ioaddr->cmd_addr + SCC_REG_LBAH;
+	ioaddr->device_addr = ioaddr->cmd_addr + SCC_REG_DEVICE;
+	ioaddr->status_addr = ioaddr->cmd_addr + SCC_REG_STATUS;
+	ioaddr->command_addr = ioaddr->cmd_addr + SCC_REG_CMD;
+}
+
+static int scc_host_init(struct ata_probe_ent *probe_ent)
+{
+	struct pci_dev *pdev = to_pci_dev(probe_ent->dev);
+	int rc;
+
+	rc = scc_reset_controller(probe_ent);
+	if (rc)
+		return rc;
+
+	probe_ent->n_ports = 1;
+
+	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+	if (rc)
+		return rc;
+	rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+	if (rc)
+		return rc;
+
+	scc_setup_ports(&probe_ent->port[0], probe_ent->iomap[SCC_BMID_BAR]);
+
+	pci_set_master(pdev);
+
+	return 0;
+}
+
+/**
+ *	scc_init_one - Register SCC PATA device with kernel services
+ *	@pdev: PCI device to register
+ *	@ent: Entry in scc_pci_tbl matching with @pdev
+ *
+ *	LOCKING:
+ *	Inherited from PCI layer (may sleep).
+ *
+ *	RETURNS:
+ *	Zero on success, or -ERRNO value.
+ */
+
+static int scc_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+	static int printed_version;
+	unsigned int board_idx = (unsigned int) ent->driver_data;
+	struct device *dev = &pdev->dev;
+	struct ata_probe_ent *probe_ent;
+	int rc;
+
+	if (!printed_version++)
+		dev_printk(KERN_DEBUG, &pdev->dev,
+			   "version " DRV_VERSION "\n");
+
+	rc = pcim_enable_device(pdev);
+	if (rc)
+		return rc;
+
+	rc = pcim_iomap_regions(pdev, (1 << SCC_CTRL_BAR) | (1 << SCC_BMID_BAR), DRV_NAME);
+	if (rc == -EBUSY)
+		pcim_pin_device(pdev);
+	if (rc)
+		return rc;
+
+	probe_ent = devm_kzalloc(dev, sizeof(*probe_ent), GFP_KERNEL);
+	if (!probe_ent)
+		return -ENOMEM;
+
+	probe_ent->dev = dev;
+	INIT_LIST_HEAD(&probe_ent->node);
+
+	probe_ent->sht 		= scc_port_info[board_idx].sht;
+	probe_ent->port_flags 	= scc_port_info[board_idx].flags;
+	probe_ent->pio_mask 	= scc_port_info[board_idx].pio_mask;
+	probe_ent->udma_mask 	= scc_port_info[board_idx].udma_mask;
+	probe_ent->port_ops 	= scc_port_info[board_idx].port_ops;
+
+	probe_ent->irq = pdev->irq;
+	probe_ent->irq_flags = IRQF_SHARED;
+	probe_ent->iomap = pcim_iomap_table(pdev);
+
+	rc = scc_host_init(probe_ent);
+	if (rc)
+		return rc;
+
+	if (!ata_device_add(probe_ent))
+		return -ENODEV;
+
+	devm_kfree(dev, probe_ent);
+	return 0;
+}
+
+static struct pci_driver scc_pci_driver = {
+	.name			= DRV_NAME,
+	.id_table		= scc_pci_tbl,
+	.probe			= scc_init_one,
+	.remove			= ata_pci_remove_one,
+#ifdef CONFIG_PM
+	.suspend		= ata_pci_device_suspend,
+	.resume			= ata_pci_device_resume,
+#endif
+};
+
+static int __init scc_init (void)
+{
+	int rc;
+
+	DPRINTK("pci_register_driver\n");
+	rc = pci_register_driver(&scc_pci_driver);
+	if (rc)
+		return rc;
+
+	DPRINTK("done\n");
+	return 0;
+}
+
+static void __exit scc_exit (void)
+{
+	pci_unregister_driver(&scc_pci_driver);
+}
+
+module_init(scc_init);
+module_exit(scc_exit);
+
+MODULE_AUTHOR("Toshiba corp");
+MODULE_DESCRIPTION("SCSI low-level driver for Toshiba SCC PATA controller");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, scc_pci_tbl);
+MODULE_VERSION(DRV_VERSION);

include/linux/libata.h

@@ -759,6 +759,7 @@ extern void ata_port_queue_task(struct ata_port *ap, work_func_t fn,
 extern u32 ata_wait_register(void __iomem *reg, u32 mask, u32 val,
 			     unsigned long interval_msec,
 			     unsigned long timeout_msec);
+extern unsigned int ata_dev_try_classify(struct ata_port *, unsigned int, u8 *);
 
 /*
  * Default driver ops implementations