Merge refs/heads/upstream from master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev

drivers/scsi/ahci.c

@@ -269,6 +269,8 @@ static struct pci_device_id ahci_pci_tbl[] = {
 	  board_ahci }, /* ESB2 */
 	{ PCI_VENDOR_ID_INTEL, 0x2683, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
 	  board_ahci }, /* ESB2 */
+	{ PCI_VENDOR_ID_INTEL, 0x27c6, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+	  board_ahci }, /* ICH7-M DH */
 	{ }	/* terminate list */
 };
 
@@ -584,12 +586,16 @@ static void ahci_intr_error(struct ata_port *ap, u32 irq_stat)
 
 static void ahci_eng_timeout(struct ata_port *ap)
 {
-	void *mmio = ap->host_set->mmio_base;
+	struct ata_host_set *host_set = ap->host_set;
+	void *mmio = host_set->mmio_base;
 	void *port_mmio = ahci_port_base(mmio, ap->port_no);
 	struct ata_queued_cmd *qc;
+	unsigned long flags;
 
 	DPRINTK("ENTER\n");
 
+	spin_lock_irqsave(&host_set->lock, flags);
+
 	ahci_intr_error(ap, readl(port_mmio + PORT_IRQ_STAT));
 
 	qc = ata_qc_from_tag(ap, ap->active_tag);
@@ -607,6 +613,7 @@ static void ahci_eng_timeout(struct ata_port *ap)
 		ata_qc_complete(qc, ATA_ERR);
 	}
 
+	spin_unlock_irqrestore(&host_set->lock, flags);
 }
 
 static inline int ahci_host_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
@@ -696,9 +703,6 @@ static int ahci_qc_issue(struct ata_queued_cmd *qc)
 	struct ata_port *ap = qc->ap;
 	void *port_mmio = (void *) ap->ioaddr.cmd_addr;
 
-	writel(1, port_mmio + PORT_SCR_ACT);
-	readl(port_mmio + PORT_SCR_ACT);	/* flush */
-
 	writel(1, port_mmio + PORT_CMD_ISSUE);
 	readl(port_mmio + PORT_CMD_ISSUE);	/* flush */
 

drivers/scsi/libata-scsi.c

@@ -391,6 +391,60 @@ int ata_scsi_error(struct Scsi_Host *host)
 	return 0;
 }
 
+/**
+ *	ata_scsi_start_stop_xlat - Translate SCSI START STOP UNIT command
+ *	@qc: Storage for translated ATA taskfile
+ *	@scsicmd: SCSI command to translate
+ *
+ *	Sets up an ATA taskfile to issue STANDBY (to stop) or READ VERIFY
+ *	(to start). Perhaps these commands should be preceded by
+ *	CHECK POWER MODE to see what power mode the device is already in.
+ *	[See SAT revision 5 at www.t10.org]
+ *
+ *	LOCKING:
+ *	spin_lock_irqsave(host_set lock)
+ *
+ *	RETURNS:
+ *	Zero on success, non-zero on error.
+ */
+
+static unsigned int ata_scsi_start_stop_xlat(struct ata_queued_cmd *qc,
+					     u8 *scsicmd)
+{
+	struct ata_taskfile *tf = &qc->tf;
+
+	tf->flags |= ATA_TFLAG_DEVICE | ATA_TFLAG_ISADDR;
+	tf->protocol = ATA_PROT_NODATA;
+	if (scsicmd[1] & 0x1) {
+		;	/* ignore IMMED bit, violates sat-r05 */
+	}
+	if (scsicmd[4] & 0x2)
+		return 1;	/* LOEJ bit set not supported */
+	if (((scsicmd[4] >> 4) & 0xf) != 0)
+		return 1;	/* power conditions not supported */
+	if (scsicmd[4] & 0x1) {
+		tf->nsect = 1;	/* 1 sector, lba=0 */
+		tf->lbah = 0x0;
+		tf->lbam = 0x0;
+		tf->lbal = 0x0;
+		tf->device |= ATA_LBA;
+		tf->command = ATA_CMD_VERIFY;	/* READ VERIFY */
+	} else {
+		tf->nsect = 0;	/* time period value (0 implies now) */
+		tf->command = ATA_CMD_STANDBY;
+		/* Consider: ATA STANDBY IMMEDIATE command */
+	}
+	/*
+	 * Standby and Idle condition timers could be implemented but that
+	 * would require libata to implement the Power condition mode page
+	 * and allow the user to change it. Changing mode pages requires
+	 * MODE SELECT to be implemented.
+	 */
+
+	return 0;
+}
+
+
 /**
  *	ata_scsi_flush_xlat - Translate SCSI SYNCHRONIZE CACHE command
  *	@qc: Storage for translated ATA taskfile
@@ -576,11 +630,19 @@ static unsigned int ata_scsi_rw_xlat(struct ata_queued_cmd *qc, u8 *scsicmd)
 		tf->lbah = scsicmd[3];
 
 		VPRINTK("ten-byte command\n");
+		if (qc->nsect == 0) /* we don't support length==0 cmds */
+			return 1;
 		return 0;
 	}
 
 	if (scsicmd[0] == READ_6 || scsicmd[0] == WRITE_6) {
 		qc->nsect = tf->nsect = scsicmd[4];
+		if (!qc->nsect) {
+			qc->nsect = 256;
+			if (lba48)
+				tf->hob_nsect = 1;
+		}
+
 		tf->lbal = scsicmd[3];
 		tf->lbam = scsicmd[2];
 		tf->lbah = scsicmd[1] & 0x1f; /* mask out reserved bits */
@@ -620,6 +682,8 @@ static unsigned int ata_scsi_rw_xlat(struct ata_queued_cmd *qc, u8 *scsicmd)
 		tf->lbah = scsicmd[7];
 
 		VPRINTK("sixteen-byte command\n");
+		if (qc->nsect == 0) /* we don't support length==0 cmds */
+			return 1;
 		return 0;
 	}
 
@@ -1435,6 +1499,8 @@ static inline ata_xlat_func_t ata_get_xlat_func(struct ata_device *dev, u8 cmd)
 	case VERIFY:
 	case VERIFY_16:
 		return ata_scsi_verify_xlat;
+	case START_STOP:
+		return ata_scsi_start_stop_xlat;
 	}
 
 	return NULL;

drivers/scsi/sata_nv.c

@@ -20,6 +20,12 @@
  *  If you do not delete the provisions above, a recipient may use your
  *  version of this file under either the OSL or the GPL.
  *
+ *  0.08
+ *     - Added support for MCP51 and MCP55.
+ *
+ *  0.07
+ *     - Added support for RAID class code.
+ *
  *  0.06
  *     - Added generic SATA support by using a pci_device_id that filters on
  *       the IDE storage class code.
@@ -48,7 +54,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME			"sata_nv"
-#define DRV_VERSION			"0.6"
+#define DRV_VERSION			"0.8"
 
 #define NV_PORTS			2
 #define NV_PIO_MASK			0x1f
@@ -116,7 +122,9 @@ enum nv_host_type
 	GENERIC,
 	NFORCE2,
 	NFORCE3,
-	CK804
+	CK804,
+	MCP51,
+	MCP55
 };
 
 static struct pci_device_id nv_pci_tbl[] = {
@@ -134,9 +142,18 @@ static struct pci_device_id nv_pci_tbl[] = {
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0, CK804 },
 	{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_SATA2,
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0, CK804 },
+	{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA,
+		PCI_ANY_ID, PCI_ANY_ID, 0, 0, MCP51 },
+	{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2,
+		PCI_ANY_ID, PCI_ANY_ID, 0, 0, MCP51 },
+	{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA,
+		PCI_ANY_ID, PCI_ANY_ID, 0, 0, MCP55 },
 	{ PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID,
 		PCI_ANY_ID, PCI_ANY_ID,
 		PCI_CLASS_STORAGE_IDE<<8, 0xffff00, GENERIC },
+	{ PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID,
+		PCI_ANY_ID, PCI_ANY_ID,
+		PCI_CLASS_STORAGE_RAID<<8, 0xffff00, GENERIC },
 	{ 0, } /* terminate list */
 };
 
@@ -274,7 +291,8 @@ static irqreturn_t nv_interrupt (int irq, void *dev_instance,
 		struct ata_port *ap;
 
 		ap = host_set->ports[i];
-		if (ap && (!(ap->flags & ATA_FLAG_PORT_DISABLED))) {
+		if (ap &&
+		    !(ap->flags & (ATA_FLAG_PORT_DISABLED | ATA_FLAG_NOINTR))) {
 			struct ata_queued_cmd *qc;
 
 			qc = ata_qc_from_tag(ap, ap->active_tag);

drivers/scsi/sata_promise.c

@@ -181,6 +181,10 @@ static struct pci_device_id pdc_ata_pci_tbl[] = {
 	  board_20319 },
 	{ PCI_VENDOR_ID_PROMISE, 0x3319, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
 	  board_20319 },
+	{ PCI_VENDOR_ID_PROMISE, 0x3519, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+	  board_20319 },
+	{ PCI_VENDOR_ID_PROMISE, 0x3d17, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+	  board_20319 },
 	{ PCI_VENDOR_ID_PROMISE, 0x3d18, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
 	  board_20319 },
 
@@ -321,11 +325,15 @@ static void pdc_qc_prep(struct ata_queued_cmd *qc)
 
 static void pdc_eng_timeout(struct ata_port *ap)
 {
+	struct ata_host_set *host_set = ap->host_set;
 	u8 drv_stat;
 	struct ata_queued_cmd *qc;
+	unsigned long flags;
 
 	DPRINTK("ENTER\n");
 
+	spin_lock_irqsave(&host_set->lock, flags);
+
 	qc = ata_qc_from_tag(ap, ap->active_tag);
 	if (!qc) {
 		printk(KERN_ERR "ata%u: BUG: timeout without command\n",
@@ -359,6 +367,7 @@ static void pdc_eng_timeout(struct ata_port *ap)
 	}
 
 out:
+	spin_unlock_irqrestore(&host_set->lock, flags);
 	DPRINTK("EXIT\n");
 }
 
@@ -441,7 +450,8 @@ static irqreturn_t pdc_interrupt (int irq, void *dev_instance, struct pt_regs *r
 		VPRINTK("port %u\n", i);
 		ap = host_set->ports[i];
 		tmp = mask & (1 << (i + 1));
-		if (tmp && ap && (!(ap->flags & ATA_FLAG_PORT_DISABLED))) {
+		if (tmp && ap &&
+		    !(ap->flags & (ATA_FLAG_PORT_DISABLED | ATA_FLAG_NOINTR))) {
 			struct ata_queued_cmd *qc;
 
 			qc = ata_qc_from_tag(ap, ap->active_tag);

drivers/scsi/sata_qstor.c

@@ -117,7 +117,7 @@ static void qs_phy_reset(struct ata_port *ap);
 static void qs_qc_prep(struct ata_queued_cmd *qc);
 static int qs_qc_issue(struct ata_queued_cmd *qc);
 static int qs_check_atapi_dma(struct ata_queued_cmd *qc);
-static void qs_bmdma_stop(struct ata_port *ap);
+static void qs_bmdma_stop(struct ata_queued_cmd *qc);
 static u8 qs_bmdma_status(struct ata_port *ap);
 static void qs_irq_clear(struct ata_port *ap);
 static void qs_eng_timeout(struct ata_port *ap);
@@ -198,7 +198,7 @@ static int qs_check_atapi_dma(struct ata_queued_cmd *qc)
 	return 1;	/* ATAPI DMA not supported */
 }
 
-static void qs_bmdma_stop(struct ata_port *ap)
+static void qs_bmdma_stop(struct ata_queued_cmd *qc)
 {
 	/* nothing */
 }
@@ -386,7 +386,8 @@ static inline unsigned int qs_intr_pkt(struct ata_host_set *host_set)
 			DPRINTK("SFF=%08x%08x: sCHAN=%u sHST=%d sDST=%02x\n",
 					sff1, sff0, port_no, sHST, sDST);
 			handled = 1;
-			if (ap && (!(ap->flags & ATA_FLAG_PORT_DISABLED))) {
+			if (ap && !(ap->flags &
+				    (ATA_FLAG_PORT_DISABLED|ATA_FLAG_NOINTR))) {
 				struct ata_queued_cmd *qc;
 				struct qs_port_priv *pp = ap->private_data;
 				if (!pp || pp->state != qs_state_pkt)
@@ -417,7 +418,8 @@ static inline unsigned int qs_intr_mmio(struct ata_host_set *host_set)
 	for (port_no = 0; port_no < host_set->n_ports; ++port_no) {
 		struct ata_port *ap;
 		ap = host_set->ports[port_no];
-		if (ap && (!(ap->flags & ATA_FLAG_PORT_DISABLED))) {
+		if (ap &&
+		    !(ap->flags & (ATA_FLAG_PORT_DISABLED | ATA_FLAG_NOINTR))) {
 			struct ata_queued_cmd *qc;
 			struct qs_port_priv *pp = ap->private_data;
 			if (!pp || pp->state != qs_state_mmio)

drivers/scsi/sata_sil.c

@@ -24,6 +24,11 @@
  *  If you do not delete the provisions above, a recipient may use your
  *  version of this file under either the OSL or the GPL.
  *
+ *  Documentation for SiI 3112:
+ *  http://gkernel.sourceforge.net/specs/sii/3112A_SiI-DS-0095-B2.pdf.bz2
+ *
+ *  Other errata and documentation available under NDA.
+ *
  */
 
 #include <linux/kernel.h>
@@ -41,8 +46,11 @@
 #define DRV_VERSION	"0.9"
 
 enum {
+	SIL_FLAG_MOD15WRITE	= (1 << 30),
+
 	sil_3112		= 0,
-	sil_3114		= 1,
+	sil_3112_m15w		= 1,
+	sil_3114		= 2,
 
 	SIL_FIFO_R0		= 0x40,
 	SIL_FIFO_W0		= 0x41,
@@ -76,13 +84,13 @@ static void sil_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
 static void sil_post_set_mode (struct ata_port *ap);
 
 static struct pci_device_id sil_pci_tbl[] = {
-	{ 0x1095, 0x3112, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
-	{ 0x1095, 0x0240, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
+	{ 0x1095, 0x3112, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
+	{ 0x1095, 0x0240, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
 	{ 0x1095, 0x3512, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
 	{ 0x1095, 0x3114, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3114 },
-	{ 0x1002, 0x436e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
-	{ 0x1002, 0x4379, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
-	{ 0x1002, 0x437a, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
+	{ 0x1002, 0x436e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
+	{ 0x1002, 0x4379, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
+	{ 0x1002, 0x437a, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
 	{ }	/* terminate list */
 };
 
@@ -174,6 +182,16 @@ static struct ata_port_info sil_port_info[] = {
 		.mwdma_mask	= 0x07,			/* mwdma0-2 */
 		.udma_mask	= 0x3f,			/* udma0-5 */
 		.port_ops	= &sil_ops,
+	}, /* sil_3112_15w - keep it sync'd w/ sil_3112 */
+	{
+		.sht		= &sil_sht,
+		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+				  ATA_FLAG_SRST | ATA_FLAG_MMIO |
+				  SIL_FLAG_MOD15WRITE,
+		.pio_mask	= 0x1f,			/* pio0-4 */
+		.mwdma_mask	= 0x07,			/* mwdma0-2 */
+		.udma_mask	= 0x3f,			/* udma0-5 */
+		.port_ops	= &sil_ops,
 	}, /* sil_3114 */
 	{
 		.sht		= &sil_sht,
@@ -331,7 +349,7 @@ static void sil_dev_config(struct ata_port *ap, struct ata_device *dev)
 		}
 
 	/* limit requests to 15 sectors */
-	if (quirks & SIL_QUIRK_MOD15WRITE) {
+	if ((ap->flags & SIL_FLAG_MOD15WRITE) && (quirks & SIL_QUIRK_MOD15WRITE)) {
 		printk(KERN_INFO "ata%u(%u): applying Seagate errata fix\n",
 		       ap->id, dev->devno);
 		ap->host->max_sectors = 15;

drivers/scsi/sata_sx4.c

@@ -825,7 +825,8 @@ static irqreturn_t pdc20621_interrupt (int irq, void *dev_instance, struct pt_re
 			ap = host_set->ports[port_no];
 		tmp = mask & (1 << i);
 		VPRINTK("seq %u, port_no %u, ap %p, tmp %x\n", i, port_no, ap, tmp);
-		if (tmp && ap && (!(ap->flags & ATA_FLAG_PORT_DISABLED))) {
+		if (tmp && ap &&
+		    !(ap->flags & (ATA_FLAG_PORT_DISABLED | ATA_FLAG_NOINTR))) {
 			struct ata_queued_cmd *qc;
 
 			qc = ata_qc_from_tag(ap, ap->active_tag);
@@ -847,10 +848,14 @@ static irqreturn_t pdc20621_interrupt (int irq, void *dev_instance, struct pt_re
 static void pdc_eng_timeout(struct ata_port *ap)
 {
 	u8 drv_stat;
+	struct ata_host_set *host_set = ap->host_set;
 	struct ata_queued_cmd *qc;
+	unsigned long flags;
 
 	DPRINTK("ENTER\n");
 
+	spin_lock_irqsave(&host_set->lock, flags);
+
 	qc = ata_qc_from_tag(ap, ap->active_tag);
 	if (!qc) {
 		printk(KERN_ERR "ata%u: BUG: timeout without command\n",
@@ -884,6 +889,7 @@ static void pdc_eng_timeout(struct ata_port *ap)
 	}
 
 out:
+	spin_unlock_irqrestore(&host_set->lock, flags);
 	DPRINTK("EXIT\n");
 }
 

drivers/scsi/sata_vsc.c

@@ -173,7 +173,8 @@ static irqreturn_t vsc_sata_interrupt (int irq, void *dev_instance,
 			struct ata_port *ap;
 
 			ap = host_set->ports[i];
-			if (ap && (!(ap->flags & ATA_FLAG_PORT_DISABLED))) {
+			if (ap && !(ap->flags &
+				    (ATA_FLAG_PORT_DISABLED|ATA_FLAG_NOINTR))) {
 				struct ata_queued_cmd *qc;
 
 				qc = ata_qc_from_tag(ap, ap->active_tag);

include/linux/ata.h

@@ -108,6 +108,8 @@ enum {
 
 	/* ATA device commands */
 	ATA_CMD_CHK_POWER	= 0xE5, /* check power mode */
+	ATA_CMD_STANDBY		= 0xE2, /* place in standby power mode */
+	ATA_CMD_IDLE		= 0xE3, /* place in idle power mode */
 	ATA_CMD_EDD		= 0x90,	/* execute device diagnostic */
 	ATA_CMD_FLUSH		= 0xE7,
 	ATA_CMD_FLUSH_EXT	= 0xEA,

include/linux/libata.h

@@ -113,6 +113,8 @@ enum {
 	ATA_FLAG_MMIO		= (1 << 6), /* use MMIO, not PIO */
 	ATA_FLAG_SATA_RESET	= (1 << 7), /* use COMRESET */
 	ATA_FLAG_PIO_DMA	= (1 << 8), /* PIO cmds via DMA */
+	ATA_FLAG_NOINTR		= (1 << 9), /* FIXME: Remove this once
+					     * proper HSM is in place. */
 
 	ATA_QCFLAG_ACTIVE	= (1 << 1), /* cmd not yet ack'd to scsi lyer */
 	ATA_QCFLAG_SG		= (1 << 3), /* have s/g table? */
@@ -363,7 +365,7 @@ struct ata_port_operations {
 
 	void (*host_stop) (struct ata_host_set *host_set);
 
-	void (*bmdma_stop) (struct ata_port *ap);
+	void (*bmdma_stop) (struct ata_queued_cmd *qc);
 	u8   (*bmdma_status) (struct ata_port *ap);
 };
 
@@ -424,7 +426,7 @@ extern void ata_dev_id_string(u16 *id, unsigned char *s,
 extern void ata_dev_config(struct ata_port *ap, unsigned int i);
 extern void ata_bmdma_setup (struct ata_queued_cmd *qc);
 extern void ata_bmdma_start (struct ata_queued_cmd *qc);
-extern void ata_bmdma_stop(struct ata_port *ap);
+extern void ata_bmdma_stop(struct ata_queued_cmd *qc);
 extern u8   ata_bmdma_status(struct ata_port *ap);
 extern void ata_bmdma_irq_clear(struct ata_port *ap);
 extern void ata_qc_complete(struct ata_queued_cmd *qc, u8 drv_stat);

include/linux/pci_ids.h

@@ -1249,6 +1249,7 @@
 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA	0x0266
 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2	0x0267
 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE	0x036E
+#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA	0x036F
 #define PCI_DEVICE_ID_NVIDIA_NVENET_12		0x0268
 #define PCI_DEVICE_ID_NVIDIA_NVENET_13		0x0269
 #define PCI_DEVICE_ID_NVIDIA_MCP51_AUDIO	0x026B