Merge master.kernel.org:/home/rmk/linux-2.6-arm

arch/arm/common/rtctime.c

@@ -128,19 +128,27 @@ EXPORT_SYMBOL(rtc_tm_to_time);
 /*
  * Calculate the next alarm time given the requested alarm time mask
  * and the current time.
- *
- * FIXME: for now, we just copy the alarm time because we're lazy (and
- * is therefore buggy - setting a 10am alarm at 8pm will not result in
- * the alarm triggering.)
  */
 void rtc_next_alarm_time(struct rtc_time *next, struct rtc_time *now, struct rtc_time *alrm)
 {
+	unsigned long next_time;
+	unsigned long now_time;
+
 	next->tm_year = now->tm_year;
 	next->tm_mon = now->tm_mon;
 	next->tm_mday = now->tm_mday;
 	next->tm_hour = alrm->tm_hour;
 	next->tm_min = alrm->tm_min;
 	next->tm_sec = alrm->tm_sec;
+
+	rtc_tm_to_time(now, &now_time);
+	rtc_tm_to_time(next, &next_time);
+
+	if (next_time < now_time) {
+		/* Advance one day */
+		next_time += 60 * 60 * 24;
+		rtc_time_to_tm(next_time, next);
+	}
 }
 
 static inline int rtc_read_time(struct rtc_ops *ops, struct rtc_time *tm)

arch/arm/kernel/entry-armv.S

@@ -566,7 +566,7 @@ ENTRY(__switch_to)
 	ldr	r6, [r2, #TI_CPU_DOMAIN]!
 #endif
 #if __LINUX_ARM_ARCH__ >= 6
-#ifdef CONFIG_CPU_MPCORE
+#ifdef CONFIG_CPU_32v6K
 	clrex
 #else
 	strex	r5, r4, [ip]			@ Clear exclusive monitor

arch/arm/kernel/traps.c

@@ -19,6 +19,7 @@
 #include <linux/personality.h>
 #include <linux/ptrace.h>
 #include <linux/kallsyms.h>
+#include <linux/delay.h>
 #include <linux/init.h>
 
 #include <asm/atomic.h>
@@ -231,6 +232,13 @@ NORET_TYPE void die(const char *str, struct pt_regs *regs, int err)
 	__die(str, err, thread, regs);
 	bust_spinlocks(0);
 	spin_unlock_irq(&die_lock);
+
+	if (panic_on_oops) {
+		printk(KERN_EMERG "Fatal exception: panic in 5 seconds\n");
+		ssleep(5);
+		panic("Fatal exception");
+	}
+
 	do_exit(SIGSEGV);
 }
 

arch/arm/mach-at91rm9200/devices.c

@@ -100,8 +100,10 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
-	if (data->pullup_pin)
+	if (data->pullup_pin) {
 		at91_set_gpio_output(data->pullup_pin, 0);
+		at91_set_multi_drive(data->pullup_pin, 1);
+	}
 
 	udc_data = *data;
 	platform_device_register(&at91rm9200_udc_device);

arch/arm/mach-at91rm9200/gpio.c

@@ -159,6 +159,23 @@ int __init_or_module at91_set_deglitch(unsigned pin, int is_on)
 }
 EXPORT_SYMBOL(at91_set_deglitch);
 
+/*
+ * enable/disable the multi-driver; This is only valid for output and
+ * allows the output pin to run as an open collector output.
+ */
+int __init_or_module at91_set_multi_drive(unsigned pin, int is_on)
+{
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
+
+	if (!pio)
+		return -EINVAL;
+
+	__raw_writel(mask, pio + (is_on ? PIO_MDER : PIO_MDDR));
+	return 0;
+}
+EXPORT_SYMBOL(at91_set_multi_drive);
+
 /*--------------------------------------------------------------------------*/
 
 

arch/arm/mach-ixp4xx/common.c

@@ -111,24 +111,30 @@ static int ixp4xx_set_irq_type(unsigned int irq, unsigned int type)
 	if (line < 0)
 		return -EINVAL;
 
-	if (type & IRQT_BOTHEDGE) {
+	switch (type){
+	case IRQT_BOTHEDGE:
 		int_style = IXP4XX_GPIO_STYLE_TRANSITIONAL;
 		irq_type = IXP4XX_IRQ_EDGE;
-	} else  if (type & IRQT_RISING) {
+		break;
+	case IRQT_RISING:
 		int_style = IXP4XX_GPIO_STYLE_RISING_EDGE;
 		irq_type = IXP4XX_IRQ_EDGE;
-	} else if (type & IRQT_FALLING) {
+		break;
+	case IRQT_FALLING:
 		int_style = IXP4XX_GPIO_STYLE_FALLING_EDGE;
 		irq_type = IXP4XX_IRQ_EDGE;
-	} else if (type & IRQT_HIGH) {
+		break;
+	case IRQT_HIGH:
 		int_style = IXP4XX_GPIO_STYLE_ACTIVE_HIGH;
 		irq_type = IXP4XX_IRQ_LEVEL;
-	} else if (type & IRQT_LOW) {
+		break;
+	case IRQT_LOW:
 		int_style = IXP4XX_GPIO_STYLE_ACTIVE_LOW;
 		irq_type = IXP4XX_IRQ_LEVEL;
-	} else
+		break;
+	default:
 		return -EINVAL;
-
+	}
 	ixp4xx_config_irq(irq, irq_type);
 
 	if (line >= 8) {	/* pins 8-15 */

arch/arm/mach-ixp4xx/nslu2-power.c

@@ -77,6 +77,9 @@ static int __init nslu2_power_init(void)
 
 static void __exit nslu2_power_exit(void)
 {
+	if (!(machine_is_nslu2()))
+		return;
+
 	free_irq(NSLU2_RB_IRQ, NULL);
 	free_irq(NSLU2_PB_IRQ, NULL);
 }

arch/arm/mach-ixp4xx/nslu2-setup.c

@@ -50,6 +50,12 @@ static struct platform_device nslu2_i2c_controller = {
 	.num_resources		= 0,
 };
 
+static struct platform_device nslu2_beeper = {
+	.name			= "ixp4xx-beeper",
+	.id			= NSLU2_GPIO_BUZZ,
+	.num_resources		= 0,
+};
+
 static struct resource nslu2_uart_resources[] = {
 	{
 		.start		= IXP4XX_UART1_BASE_PHYS,
@@ -97,6 +103,7 @@ static struct platform_device *nslu2_devices[] __initdata = {
 	&nslu2_i2c_controller,
 	&nslu2_flash,
 	&nslu2_uart,
+	&nslu2_beeper,
 };
 
 static void nslu2_power_off(void)

arch/arm/mach-versatile/pci.c

@@ -240,6 +240,14 @@ int __init pci_versatile_setup(int nr, struct pci_sys_data *sys)
         int i;
         int myslot = -1;
 	unsigned long val;
+	void __iomem *local_pci_cfg_base;
+
+	val = __raw_readl(SYS_PCICTL);
+	if (!(val & 1)) {
+		printk("Not plugged into PCI backplane!\n");
+		ret = -EIO;
+		goto out;
+	}
 
 	if (nr == 0) {
 		sys->mem_offset = 0;
@@ -253,47 +261,44 @@ int __init pci_versatile_setup(int nr, struct pci_sys_data *sys)
 		goto out;
 	}
 
-	__raw_writel(VERSATILE_PCI_MEM_BASE0 >> 28,PCI_IMAP0);
-	__raw_writel(VERSATILE_PCI_MEM_BASE1 >> 28,PCI_IMAP1);
-	__raw_writel(VERSATILE_PCI_MEM_BASE2 >> 28,PCI_IMAP2);
-
-	__raw_writel(1, SYS_PCICTL);
-
-	val = __raw_readl(SYS_PCICTL);
-	if (!(val & 1)) {
-		printk("Not plugged into PCI backplane!\n");
-		ret = -EIO;
-		goto out;
-	}
-
 	/*
 	 *  We need to discover the PCI core first to configure itself
 	 *  before the main PCI probing is performed
 	 */
-	for (i=0; i<32; i++) {
+	for (i=0; i<32; i++)
 		if ((__raw_readl(VERSATILE_PCI_VIRT_BASE+(i<<11)+DEVICE_ID_OFFSET) == VP_PCI_DEVICE_ID) &&
 		    (__raw_readl(VERSATILE_PCI_VIRT_BASE+(i<<11)+CLASS_ID_OFFSET) == VP_PCI_CLASS_ID)) {
 			myslot = i;
-
-			__raw_writel(myslot, PCI_SELFID);
-			val = __raw_readl(VERSATILE_PCI_CFG_VIRT_BASE+(myslot<<11)+CSR_OFFSET);
-			val |= (1<<2);
-			__raw_writel(val, VERSATILE_PCI_CFG_VIRT_BASE+(myslot<<11)+CSR_OFFSET);
 			break;
 		}
-	}
 
 	if (myslot == -1) {
 		printk("Cannot find PCI core!\n");
 		ret = -EIO;
-	} else {
+		goto out;
+	}
+
 	printk("PCI core found (slot %d)\n",myslot);
-		/* Do not to map Versatile FPGA PCI device
-		   into memory space as we are short of
-		   mappable memory */
+
+	__raw_writel(myslot, PCI_SELFID);
+	local_pci_cfg_base = (void *) VERSATILE_PCI_CFG_VIRT_BASE + (myslot << 11);
+
+	val = __raw_readl(local_pci_cfg_base + CSR_OFFSET);
+	val |= PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER | PCI_COMMAND_INVALIDATE;
+	__raw_writel(val, local_pci_cfg_base + CSR_OFFSET);
+
+	/*
+	 * Configure the PCI inbound memory windows to be 1:1 mapped to SDRAM
+	 */
+	__raw_writel(PHYS_OFFSET, local_pci_cfg_base + PCI_BASE_ADDRESS_0);
+	__raw_writel(PHYS_OFFSET, local_pci_cfg_base + PCI_BASE_ADDRESS_1);
+	__raw_writel(PHYS_OFFSET, local_pci_cfg_base + PCI_BASE_ADDRESS_2);
+
+	/*
+	 * Do not to map Versatile FPGA PCI device into memory space
+	 */
 	pci_slot_ignore |= (1 << myslot);
 	ret = 1;
-	}
 
  out:
 	return ret;
@@ -305,18 +310,18 @@ struct pci_bus *pci_versatile_scan_bus(int nr, struct pci_sys_data *sys)
 	return pci_scan_bus(sys->busnr, &pci_versatile_ops, sys);
 }
 
-/*
- * V3_LB_BASE? - local bus address
- * V3_LB_MAP?  - pci bus address
- */
 void __init pci_versatile_preinit(void)
 {
-}
+	__raw_writel(VERSATILE_PCI_MEM_BASE0 >> 28, PCI_IMAP0);
+	__raw_writel(VERSATILE_PCI_MEM_BASE1 >> 28, PCI_IMAP1);
+	__raw_writel(VERSATILE_PCI_MEM_BASE2 >> 28, PCI_IMAP2);
 
-void __init pci_versatile_postinit(void)
-{
-}
+	__raw_writel(PHYS_OFFSET >> 28, PCI_SMAP0);
+	__raw_writel(PHYS_OFFSET >> 28, PCI_SMAP1);
+	__raw_writel(PHYS_OFFSET >> 28, PCI_SMAP2);
 
+	__raw_writel(1, SYS_PCICTL);
+}
 
 /*
  * map the specified device/slot/pin to an IRQ.   Different backplanes may need to modify this.
@@ -327,15 +332,14 @@ static int __init versatile_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
 	int devslot = PCI_SLOT(dev->devfn);
 
 	/* slot,  pin,	irq
-	    24	  1	27
-	    25    1	28	untested
-	    26	  1	29
-	    27    1	30	untested
+	 *  24     1     27
+	 *  25     1     28
+	 *  26     1     29
+	 *  27     1     30
 	 */
+	irq = 27 + ((slot + pin - 1) & 3);
 
-	irq = 27 + ((slot + pin + 2) % 3);	/* Fudged */
-
-	printk("map irq: slot %d, pin %d, devslot %d, irq: %d\n",slot,pin,devslot,irq);
+	printk("PCI map irq: slot %d, pin %d, devslot %d, irq: %d\n",slot,pin,devslot,irq);
 
 	return irq;
 }
@@ -347,7 +351,6 @@ static struct hw_pci versatile_pci __initdata = {
 	.setup			= pci_versatile_setup,
 	.scan			= pci_versatile_scan_bus,
 	.preinit		= pci_versatile_preinit,
-	.postinit		= pci_versatile_postinit,
 };
 
 static int __init versatile_pci_init(void)

arch/arm/mm/abort-ev6.S

@@ -20,7 +20,7 @@
  */
 	.align	5
 ENTRY(v6_early_abort)
-#ifdef CONFIG_CPU_MPCORE
+#ifdef CONFIG_CPU_32v6K
 	clrex
 #else
 	strex	r0, r1, [sp]			@ Clear the exclusive monitor

arch/arm/tools/mach-types

@@ -12,7 +12,7 @@
 #
 #   http://www.arm.linux.org.uk/developer/machines/?action=new
 #
-# Last update: Mon Jan 9 12:56:42 2006
+# Last update: Mon Feb 20 10:18:02 2006
 #
 # machine_is_xxx	CONFIG_xxxx		MACH_TYPE_xxx		number
 #
@@ -904,7 +904,7 @@ wg302v2			MACH_WG302V2		WG302V2			890
 eb42x			MACH_EB42X		EB42X			891
 iq331es			MACH_IQ331ES		IQ331ES			892
 cosydsp			MACH_COSYDSP		COSYDSP			893
-uplat7d			MACH_UPLAT7D		UPLAT7D			894
+uplat7d_proto		MACH_UPLAT7D		UPLAT7D			894
 ptdavinci		MACH_PTDAVINCI		PTDAVINCI		895
 mbus			MACH_MBUS		MBUS			896
 nadia2vb		MACH_NADIA2VB		NADIA2VB		897
@@ -938,3 +938,34 @@ auckland		MACH_AUCKLAND		AUCKLAND		924
 ak3220m			MACH_AK3320M		AK3320M			925
 duramax			MACH_DURAMAX		DURAMAX			926
 n35			MACH_N35		N35			927
+pronghorn		MACH_PRONGHORN		PRONGHORN		928
+fundy			MACH_FUNDY		FUNDY			929
+logicpd_pxa270		MACH_LOGICPD_PXA270	LOGICPD_PXA270		930
+cpu777			MACH_CPU777		CPU777			931
+simicon9201		MACH_SIMICON9201	SIMICON9201		932
+leap2_hpm		MACH_LEAP2_HPM		LEAP2_HPM		933
+cm922txa10		MACH_CM922TXA10		CM922TXA10		934
+sandgate		MACH_PXA		PXA			935
+sandgate2		MACH_SANDGATE2		SANDGATE2		936
+sandgate2g		MACH_SANDGATE2G		SANDGATE2G		937
+sandgate2p		MACH_SANDGATE2P		SANDGATE2P		938
+fred_jack		MACH_FRED_JACK		FRED_JACK		939
+ttg_color1		MACH_TTG_COLOR1		TTG_COLOR1		940
+nxeb500hmi		MACH_NXEB500HMI		NXEB500HMI		941
+netdcu8			MACH_NETDCU8		NETDCU8			942
+ml675050_cpu_boa	MACH_ML675050_CPU_BOA	ML675050_CPU_BOA	943
+ng_fvx538		MACH_NG_FVX538		NG_FVX538		944
+ng_fvs338		MACH_NG_FVS338		NG_FVS338		945
+pnx4103			MACH_PNX4103		PNX4103			946
+hesdb			MACH_HESDB		HESDB			947
+xsilo			MACH_XSILO		XSILO			948
+espresso		MACH_ESPRESSO		ESPRESSO		949
+emlc			MACH_EMLC		EMLC			950
+sisteron		MACH_SISTERON		SISTERON		951
+rx1950			MACH_RX1950		RX1950			952
+tsc_venus		MACH_TSC_VENUS		TSC_VENUS		953
+ds101j			MACH_DS101J		DS101J			954
+mxc300_30ads		MACH_MXC30030ADS	MXC30030ADS		955
+fujitsu_wimaxsoc	MACH_FUJITSU_WIMAXSOC	FUJITSU_WIMAXSOC	956
+dualpcmodem		MACH_DUALPCMODEM	DUALPCMODEM		957
+gesbc9312		MACH_GESBC9312		GESBC9312		958

include/asm-arm/arch-at91rm9200/gpio.h

@@ -183,6 +183,7 @@ extern int at91_set_B_periph(unsigned pin, int use_pullup);
 extern int at91_set_gpio_input(unsigned pin, int use_pullup);
 extern int at91_set_gpio_output(unsigned pin, int value);
 extern int at91_set_deglitch(unsigned pin, int is_on);
+extern int at91_set_multi_drive(unsigned pin, int is_on);
 
 /* callable at any time */
 extern int at91_set_gpio_value(unsigned pin, int value);

include/asm-arm/arch-ixp4xx/nas100d.h

@@ -19,8 +19,8 @@
 #error "Do not include this directly, instead #include <asm/hardware.h>"
 #endif
 
-#define NAS100D_SDA_PIN		6
-#define NAS100D_SCL_PIN		5
+#define NAS100D_SDA_PIN		5
+#define NAS100D_SCL_PIN		6
 
 /*
  * NAS100D PCI IRQs